【求助】problems get smc2632w v.3 working on fedora4
sorry for my poor english, no chinese input on systemhi guys:
I have some problems on getting my SMC2632w v.3 pcmcia wirless network card working on my toshiba laptop
because this card is using the atmel chips, the driver which i used is from
atmelwlandriver.sourceforge.net
just follow the drivers readme, make, make install etc....everything is fine, after restart the pcmcia service, it seems that the status lights on my card start flashing(it doesn't work before). the module which I used is pcmf502rd. here is the msg from iwconfig
here is the msg from ifconfig
[CODE]atml0 ATMEL REVD ESSID:"MIT" Nickname:""
NWIDff/any Mode:Managed Frequency=2.437 GHz
Access Point: 00:0A:EB:D2:7B:F0 Bit Rate=11 Mb/s Tx-Power=20 dBm
Sensitivity:0/0
Retryn RTS thrff Fragment thrff
Encryption keyff
Power Managementff
Link Quality=0/100 Signal level=60/100 Noise level=0/0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0[/CODE]
[QUOTE][b]atml0 Link encap:Ethernet HWaddr 00:04:E2:79:D7:FB [/b]
[b]inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0[/b]
[b]inet6 addr: fe80::204:e2ff:fe79:d7fb/64 Scope:Link[/b]
[b]UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1[/b]
[b]RX packets:352 errors:0 dropped:0 overruns:0 frame:0[/b]
[b]TX packets:0 errors:0 dropped:0 overruns:0 carrier:0[/b]
[b]collisions:0 txqueuelen:1000 [/b]
[b]RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)[/b]
[b]Interrupt:3 Base address:0x100 [/b]
[b]lo Link encap:Local Loopback [/b]
[b]inet addr:127.0.0.1 Mask:255.0.0.0[/b]
[b]inet6 addr: ::1/128 Scope:Host[/b]
[b]UP LOOPBACK RUNNING MTU:16436 Metric:1[/b]
[b]RX packets:1360 errors:0 dropped:0 overruns:0 frame:0[/b]
[b]TX packets:1360 errors:0 dropped:0 overruns:0 carrier:0[/b]
[b]collisions:0 txqueuelen:0 [/b]
[b]RX bytes:1393336 (1.3 MiB) TX bytes:1393336 (1.3 MiB)[/b][/QUOTE]and here is content of the file [b]ifcfg-atml0 [/b]in my [b]/etc/sysconfig/network-scrip/[/b]
[QUOTE][b]DEVICE=atml0[/b]
[b]IPV6INIT=no[/b]
[b]# Change next line to "ONBOOT=yes" to have this device start at boot[/b]
[b]ONBOOT=yes[/b]
[b]USERCTL=yes[/b]
[b]#BOOTPROTO=dhcp[/b]
[b]# Uncomment above line and comment out next 4 lines to use DHCP[/b]
[b]BOOTPROTO=none[/b]
[b]IPADDR=192.168.0.16[/b]
[b]NETMASK=255.255.255.0[/b]
[b]GATEWAY=192.168.0.1[/b]
[b]WIRELESS=yes[/b]
[b]MODE=Managed[/b]
[b]ESSID=[/b]
[b]CHANNEL=9[/b]
[b]RATE=11Mb/s[/b]
[b]#IWPRIV="mode 3"[/b]
[b]#IWCONFIG_OPTIONS=''[/b]
[b]#IWSPY_OPTIONS=''[/b]
[b]#IWPRIV_OPTIONS="mode 3"[/b]
[b]TYPE=Wireless[/b]
[b]PEERDNS=no[/b]
[b]DOMAIN=[/b]
[b]DHCP_HOSTNAME=[/b]
[b]HWADDR=00:04:e2:79:d7:fb[/b][/QUOTE]it seems that the system find that card already, and the mac address is dectect correctely, also the centre wireless access point infomation is recived by my card, but I can't get the network.when use dchp ,my card can't get IP address from the router.
by the way there is no limitation when access my wirless router, no passwaord,no user name, and the card is working fine under windows xp, anybody can help?????
页:
[1]