Linux伊甸园论坛 » Linux硬件驱动专区 » IBM X系列服务器ATI显卡安装方法

icecobra 发表于 2006-11-30 11:42

IBM X系列服务器ATI显卡安装方法

以下是IBM给出解决办法，小弟试过可行，贴出来大家共享的同时也感谢厂家技术支持。

========================================================

x系列服务器安装linux无法进入x界面是由于linux显卡驱动版本与硬件有些冲突，解决方法如下：
1.以root身份进入终端模式
2.使用vi编辑 /etc/X11/xorg.conf (由于我不太清楚FC5的显卡配置文件具体位置，这个是RHEL4U2的配置文件的位置，烦请自行查找到显卡配置文件的位置)
3、在文件中找到 "Device" 的这一项
应该可以看到是   Driver "radeon"
把radeon改为vesa
即改成           Driver "vesa"
保存退出。
4.重启即可

官方文档做法如下：（看起来是十分麻烦的，我节选一部分）
Modifications are needed to run the X Window System. After the installation, complete the following steps:
1.Log in as root.

2.Type X -configure

3.Type vi /root/xorg.conf.new

4.Scroll to the section that begins with the line Section "Monitor"

5.Using the mouse, highlight the monitor section (usually about 9 lines) by holding the left mouse button down and dragging the mouse across the area.

6.Type :q to exit the editor.

7.Type vi /etc/X11/xorg.conf

8.Scroll to the section that begins with the line Section "Monitor".

9.Place the cursor on the first line of that section. Type dd until the whole monitor section is deleted.

10.Type i to enter insertion mode.

11.Click the right mouse button to paste the new section into the file.

12.Press Esc to exit insert mode.

13.Scroll to the section which begins with the line Section "Device".

14.Complete the following steps using exact punctuation and capitalization:

     A.  Type /radeon and then press Enter.
     B.  Type dw
     C.  Type i
     D.  Type vesa so that the completed line is:
         Driver "vesa"
         and then press Esc.
     E.  Type /DPMS and then press Enter.
         F.  Type A
         G.  Type "off" so that the completed line is:
         Option "DPMS" "off"
         and then press Esc.
     H.  Type :wq to save and exit.

15.Type init 5

16.If you want the server to start the X Window System during startup, complete the following steps:
         A   Open the /etc/inittab file in a text editor.
     B   Locate the line "id:3:initdefault:" and change it to:
         id:5:initdefault:         
     C   Save and close the file.
     D   Open the /boot/grub/grub.conf file in a text editor.
     E   Locate each line that begins with "kernel" and remove the solitary "3" from the line.
     F   Save and close the file.


原文连接：[url]http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-62584&tempselected=5#45[/url]

synge 发表于 2006-11-30 22:29

[QUOTE=icecobra]
在文件中找到 "Device" 的这一项
应该可以看到是   Driver "radeon"
把radeon改为vesa
即改成           Driver "vesa"
[/QUOTE]首先这样改是可行的，但是这样改的话事实上并没有安装ATI驱动，只是选择了通用的显卡驱动并不能发挥ATI显卡的性能有点可惜了。

查看完整版本: IBM X系列服务器ATI显卡安装方法