带ｕ盘启动2410开发板不能运行ｑｔ
我把ｕ盘插在ｕｓｂ插槽上，ｒｅｓｅｔ2410开发板，在rc.local上已经添加了/sbin/mount -t vfat /dev/scsi/host0/bus0/target0/lun0/part1 /u
/Qtopia/qtopia-free-1.7.0/bin/qt -qws
不过启动到一半的时候就停下来了，把ｕ盘拔掉可以运行qt程序。
错误提示如下：
....................
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xe9000000, IRQ 26
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
port #1 suspened!
port #0 alived!
hub.c: 1 port detected
usb.c: registered new driver usb_mouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb.c: registered new driver keyboard
usbkbd.c: :USB HID Boot Protocol keyboard driver
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
VFS: Mounted root (cramfs filesystem).
Mounted devfs on /dev
Freeing init memory: 72K
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0xea0/0x6803) is not claimed by any active driver.
Reading data from NAND FLASH without ECC is not recommended
mount /etc as ramfs
re-create the /etc/mtab entries
Reading data from NAND FLASH without ECC is not recommended
UDA1341 audio driver initialized
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: OTi Model: Ultra Floppy Rev: 1.11
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 32256 512-byte hdwr sectors (17 MB)
sda: Write Protect is off
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4
USB Mass Storage support registered.
Linux video capture interface: v1.00
video_dev: unable to get major 81
insmod: init_module: videodev: Input/output error
usb.c: registered new driver ov511
ov511.c: v1.48a for Linux 2.4 : OV511 USB Camera Driver
mount: Mounting none on /proc/bus/usb failed: No such file or directory
cramfs: wrong magic
mount: Mounting /dev/mtdblock/3 on /tmp/disk3 failed: Invalid argument
init started: BusyBox v0.60.5 (2003.05.12-11:53+0000) multi-c
到这里就停下来了！！谁知道怎么解决！ cramfs 驱动是不是崩溃了
补充
如果ｕ盘不挂着，可以自动运行程序，提示信息如下：usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xe9000000, IRQ 26
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
port #1 suspened!
port #0 alived!
hub.c: 1 port detected
usb.c: registered new driver usb_mouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb.c: registered new driver keyboard
usbkbd.c: :USB HID Boot Protocol keyboard driver
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
VFS: Mounted root (cramfs filesystem).
Mounted devfs on /dev
Freeing init memory: 72K
Reading data from NAND FLASH without ECC is not recommended
mount /etc as ramfs
re-create the /etc/mtab entries
UDA1341 audio driver initialized
Reading data from NAND FLASH without ECC is not recommended
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Linux video capture interface: v1.00
video_dev: unable to get major 81
insmod: init_module: videodev: Input/output error
usb.c: registered new driver ov511
ov511.c: v1.48a for Linux 2.4 : OV511 USB Camera Driver
mount: Mounting none on /proc/bus/usb failed: No such file or directory
cramfs: wrong magic
mount: Mounting /dev/mtdblock/3 on /tmp/disk3 failed: Invalid argument
init started: BusyBox v0.60.5 (2003.05.12-11:53+0000) multi-cll binary
Reading data from NAND FLASH without ECC is not recommended
Please press Enter to activate this console. /bin/cp: will not create hard link `/tmp/Applications/Network/modules' to directory `/tmp/Applications/AlarmServer'
/bin/cp: will not create hard link `/tmp/Documents' to directory `/tmp/Applications/qimpen'
Could not open mime.types file, "etc/mime.types", for reading
/usr/etc/rc.local: line 16: /sbin/mount: No such file or directory
Reading data from NAND FLASH without ECC is not recommended
Reading data from NAND FLASH without ECC is not recommended
Reading data from NAND FLASH without ECC is not recommended
[9;0][?33l[?25l[?25lI have created thransfer file thread!
I have created timer play thread!
I have created serial thread! 如果可以运行shell,手动运行一下就知道是不是cramfs驱动崩溃了
回复 #4 AIKO_sex 的帖子
如果插着ｕ盘的时候系统启动到那里是进入不了ｓｈｅｌｌ的，你说cramfs驱动崩溃是怎么回事，如果是要怎么解决？页:
[1]