刚入门装了红旗6.0 好几遍就是上不了网，只能ping自己，右下角没有数据发送也没有数据接收，各位大侠帮忙解决一下，dmseg好像有错误，信息如下：

[root@ly`]# dmesg
Linux version 2.6.22.6-1 (root@builder2.redflag-linux.com) (gcc version 4.2.1) #
1 SMP Tue Sep 4 06:11:18 EDT 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000f4fc0
Entering add_active_range(0, 0, 131056) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   131056
  HighMem    131056 ->   131056
early_node_map[1] active PFN ranges
    0:        0 ->   131056
On node 0 totalpages: 131056
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 991 pages used for memmap
  Normal zone: 125969 pages, LIFO batch:31
  HighMem zone: 0 pages used for memmap
DMI 2.2 present.
Using APIC driver default
ACPI: RSDP 000F8EB0, 0014 (r0 Nvidia)
ACPI: RSDT 1FFF3040, 0030 (r1 Nvidia AWRDACPI 42302E31 AWRD        0)
ACPI: FACP 1FFF30C0, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD        0)
ACPI: DSDT 1FFF3180, 48C1 (r1 NVIDIA AWRDACPI     1000 MSFT  100000E)
ACPI: FACS 1FFF0000, 0040
ACPI: SRAT 1FFF7B80, 0090 (r1 AMD    HAMMER          1 AMD         1)
ACPI: APIC 1FFF7AC0, 007C (r1 Nvidia AWRDACPI 42302E31 AWRD        0)
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists.  Total pages: 130033
Kernel command line: ro root=LABEL=/ vga=788 splash=silent
bootsplash: silent mode.
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1470.020 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510692k/524224k available (2080k kernel code, 13048k reserved, 851k data
, 256k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xffe15000 - 0xfffff000   (1960 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
    lowmem  : 0xc0000000 - 0xdfff0000   ( 511 MB)
      .init : 0xc12e4000 - 0xc1324000   ( 256 kB)
      .data : 0xc12082e7 - 0xc12dd15c   ( 851 kB)
      .text : 0xc1000000 - 0xc12082e7   (2080 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2940.99 BogoMIPS (lpj=1470496)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001
00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 0000000
0 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 13k freed
ACPI: Core revision 20070126
CPU0: AMD Sempron(tm) Processor 2500+ stepping 02
Total of 1 processors activated (2940.99 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
Time:  2:09:30  Date: 03/08/108
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb7d0, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16)
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
ACPI: Power Resource [ISAV] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:00: ioport range 0x4000-0x407f has been reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff has been reserved
pnp: 00:00: ioport range 0x4800-0x487f has been reserved
pnp: 00:00: ioport range 0x4880-0x48ff has been reserved
pnp: 00:01: iomem range 0xd0000-0xd3fff has been reserved
pnp: 00:01: iomem range 0xf0000-0xf7fff could not be reserved
pnp: 00:01: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:01: iomem range 0xfc000-0xfffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:0b.0
  IO window: a000-afff
  MEM window: fdf00000-fdffffff
  PREFETCH window: d0000000-efffffff
PCI: Bridge: 0000:00:0e.0
  IO window: 9000-9fff
  MEM window: fde00000-fdefffff
  PREFETCH window: fdd00000-fddfffff
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
I　　　　　　

IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Switched to high resolution mode on CPU 0
Freeing initrd memory: 4978k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
vesafb: framebuffer at 0xe0000000, mapped to 0xe0880000, using 3750k, total 1310
72k
vesafb: mode is 800x600x16, linelength=1600, pages=135
vesafb: protected mode interface info at c000:5761
vesafb: pmi: set display start = c00c57f5, set palette = c00c5841
vesafb: pmi: ports = ac10 ac16 ac54 ac38 ac3c ac5c ac00 ac04 acb0 acb2 acb4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 29536 byt
es,<6>...found (800x600, 13029 bytes, v3).
Console: switching to colour frame buffer device 96x34
fb0: VESA VGA frame buffer device
ACPI Exception (processor_core-0781): AE_NOT_FOUND, Processor Device is not pres
ent [20070126]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hdaMA, hdbMA
    ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdcMA, hddMA
Probing IDE interface ide0...
hda: WDC WD800JB-00JJC0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: DVD-ROM BDV316G, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 >
hdd: ATAPI 40X DVD-ROM drive, 512kB Cache<4>hdd: drive side 80-wire cable detect
ion failed, limiting max speed to UDMA33

Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new interface driver libusual
PNP: PS/2 Controller [PNP0303S2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
  Magic number: 4:412:156
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 256k freed
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, high) -> IR
Q 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 16, io mem 0xfe02f000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 22 (level, high) -> IR
Q 17
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 17, io mem 0xfe02e000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IR
Q 18
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: irq 18, io mem 0xfe02d000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
SCSI subsystem initialized
libata version 2.21 loaded.
usb 2-4: new low speed USB device using ohci_hcd and address 2
usb 2-4: configuration #1 chosen from 1 choice
input: Logitech USB-PS/2 Optical Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1
-4
sata_nv 0000:00:09.0: version 3.4
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [APSI] -> GSI 20 (level, high) -> IR
Q 19
PCI: Setting latency timer of device 0000:00:09.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x000109e0 ctl 0x00010be2 bmdma 0x0001cc00 irq 19
ata2: SATA max UDMA/133 cmd 0x00010960 ctl 0x00010b62 bmdma 0x0001cc08 irq 19
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APSJ] -> GSI 23 (level, high) -> IR
Q 16
PCI: Setting latency timer of device 0000:00:0a.0 to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x000109f0 ctl 0x00010bf2 bmdma 0x0001b400 irq 16
ata4: SATA max UDMA/133 cmd 0x00010970 ctl 0x00010b72 bmdma 0x0001b408 irq 16
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ
20
eth0: RealTek RTL8139 at 0xe081e000, 00:0c:76:cf:4f:d9, IRQ 20
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 22 (level, high) -> IR
Q 17
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 50685 usecs
intel8x0: clocking to 46786
FDC 0 is a post-1991 82077
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
No dock devices found.
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.　　　　　　

device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: devel@redhat.com[/email]
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on hda8, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
fuse init (API version 7.8)
Adding 1044184k swap on /dev/hda9.  Priority:-1 extents:1 across:1044184k
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ
20
Linux agpgart interface v0.102 (c) Dave Jones
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized radeon 1.27.0 20060524 on minor 0
[drm:radeon_cp_init] *ERROR* radeon_cp_init called without lock held
[drm:drm_unlock] *ERROR* Process 1701 using kernel context 0
NETDEV WATCHDOG: eth0: transmit timed out
eth0: no IPv6 routers present
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 0008203c. (queue head)
eth0:  Tx descriptor 1 is 0008203c.
eth0:  Tx descriptor 2 is 0008205a.
eth0:  Tx descriptor 3 is 0008206e.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 0008203c. (queue head)
eth0:  Tx descriptor 1 is 0008210e.
eth0:  Tx descriptor 2 is 0008204e.
eth0:  Tx descriptor 3 is 0008210e.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 0008210e. (queue head)
eth0:  Tx descriptor 1 is 000820fc.
eth0:  Tx descriptor 2 is 00082129.
eth0:  Tx descriptor 3 is 00082129.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082046. (queue head)
eth0:  Tx descriptor 1 is 0008213d.
eth0:  Tx descriptor 2 is 00082129.
eth0:  Tx descriptor 3 is 00082110.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082114. (queue head)
eth0:  Tx descriptor 1 is 000820e3.
eth0:  Tx descriptor 2 is 000820f7.
eth0:  Tx descriptor 3 is 000820b9.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 000820a9. (queue head)
eth0:  Tx descriptor 1 is 00082056.
eth0:  Tx descriptor 2 is 0008206a.
eth0:  Tx descriptor 3 is 00082110.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082114. (queue head)
eth0:  Tx descriptor 1 is 000820e3.
eth0:  Tx descriptor 2 is 000820f7.
eth0:  Tx descriptor 3 is 000820e5.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 000820c5. (queue head)
eth0:  Tx descriptor 1 is 00082056.
eth0:  Tx descriptor 2 is 0008206a.
eth0:  Tx descriptor 3 is 00082110.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082114. (queue head)
eth0:  Tx descriptor 1 is 000820e3.
eth0:  Tx descriptor 2 is 000820f7.
eth0:  Tx descriptor 3 is 00082046.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[root@ly`]#