Linux服务器ADSL下利用NAT实现上网共享

来源:赛迪网 作者:korn
   

1、 网卡配置。

两块网卡,eth0为拨号网卡,IP:192.168.1.1(其他的地址也可);eth1为内网网卡,IP:192.168.0.1。掩码均为255.255.255.0。局域网网段为192.168.0.0。

注意:此处两块网卡均不能设网关。 拨号(PPPOE)的网卡不用设置

 

2、 PPPoE软件的升级与安装

1) 在 http://www.roaringpenguin.com/pppoe/#download 下载

2) 安装rp-pppoe。以root身份执行

rpm –Uvh rp-pppoe-3.5-1.i386.rpm

 

3、 修改/etc/ sysctl.conf

将其中的

net.ipv4.ip_forward = 0

改为

net.ipv4.ip_forward = 1

 

4、 去除ipchains模块,只选择iptables方法如下:

1)setup

2)选择system service

3)去除ipchains

4)选中iptables

5)重启机器

 

5、 PPPoE客户端配置

在rp-pppoe-3.5-1.i386.rpm安装完毕后,接下来就可进行PPPoE客户端配置了。过程如下。

#/usr/sbin/adsl-setup

>;>;>; Enter your PPPoE user name: ——此处输入拨号帐号的用户名

>;>;>; Enter the Ethernet interface connected to the ADSL modem For Solaris, this is likely to be something like /dev/hme0. For Linux, it will be ethn, where n is a number. (default eth0): ——输eth0

>;>;>; Enter the demand value (default no): ——输no

>;>;>; Enter the DNS information here: ——输210.52.149.2(视当地运营商的DNS服务器IP而定)

>;>;>; Please enter your PPPoE password: ——输网通用户口令

>;>;>; Choose a type of firewall (0-2): ——输0

>;>;>; Accept these settings and adjust configuration files (y/n)? ——输y

 

6、 启动拨号连接

/usr/sbin/adsl-start

成功连接后,屏幕显示Connected。

此时这台linux已可以上网浏览了。

 

7、 IP伪装

为了使局域网中的其他机器能通过Linux服务器共享上网,至少须执行下面的命令:

iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE

完成后,在192.168.0.0网段(网关为192.168.0.1)的PC机就可透过Linux上网了!

 

8、 开机自启动

为了使Linux服务器能够自动拨号,执行下面步骤。

1)chkconfig --add adsl

2)setup

3)选择system services

4)选中ADSL

5)OK退出

6)打开/etc/rc.d/rc.local,在该文件的末尾添上下面语句

echo "[OK]"

echo "Drop ICMP form anywhere"

echo 1 >; /proc/sys/net/ipv4/icmp_echo_ignore_all

echo "[OK]"

iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE

说明:前面四句用于关闭ICMP,防止别人Ping。

 

9、至此,一切OK,一个简单的拨号建成了。重启机器后,发现linux的internet共享连接已经一切就绪了。

(责任编辑:A6)


时间:2008-03-11 14:51 来源:赛迪网 作者:korn 原文链接

好文,顶一下
(0)
0%
文章真差,踩一下
(0)
0%
------分隔线----------------------------


把开源带在你的身边-精美linux小纪念品
无觅相关文章插件,快速提升流量